Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I have a product that needs to send 256 bytes of data to an IOS or Android phone upon request from phone. We are currently using the Nordic UART app to receive the data...
Hi,
I have an issue with OTA DFU stop working after updating softdevice_bootloader through OTA DFU, and the problem seems to be in the MBR params page.
The scenario is...
Hi everyone,
When I am scanning the advertising packets of nRF52840 peripheral, I see that Device's address is type of Random Static.
1. The Static Random Address is a...
HI, I know about the proxy feature/nodes and the way in which a smartphone can connect to a proxy node and send a message. However, in the mentioned method we need to connect...
I find that the low current readings in the Average and Trigger windows can vary significantly. I understand that the sample rates are much different, but does that also affect...
Hi,
I am trying to set the section placement macros on the segger embedded studio. Follow some instruction, find "project -> Option -> Linker" I cannot find the set about...
Hello,
I am using the coap Client example from nRF Connect SDK, which uses the Coap utils library https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include...
Hi,
I am developing a product, based on nrf52840 soc with SDK v15.3 and softdevice V14. I have a pairing problem with the recently released iOS, version14. while my product...
Hi,
I'm using the NRF52840 with the nRF5SDK (v16.0).
For my product, I'd like to enter as low-power a sleep as possible, while still being able to wake up on the on board...
Hi, I was using nRF52840 ， flash is mx25L25645GM2, I used fatfs with QSPI ,but I found fatfs was unstable,After some time, the stored file would dispear.Sometime there were...
what is credit based flow control in L2CAP connection oriented channel..?
What is meaning of credits..?
what is exact usage in IPSP ..?
How it will effect data communication...
Hello,
I am preparing sniffing workspace for BT Mesh, where I have 3 devices in the Mesh network (provided by nRF Mesh app) and I need to read SRC, DST, SEQ and simmilar...
I tried to run my Thingy91 off the battery but it shuts off instantly.
My questions is if the battery charging functionality is in the firmware or hardware? Trying to figure...
Dear Nordic support member,
Where does "pca10100e folders" be installed?
I have nRF52833 development Kit. But I could not find pca10100e folder.
Note: My IDE is IAR...
Hi, I am looking to develop applications for the nRF5340. After watching the "Introduction to Zephyr RTOS" webinar, I saw that the software engineer presenting the demo was...
