I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi!
Working on project based on nRF52810. Everything was fine until I began to work on part to save setting in flash memory.
I've used flash_fds example SDK 16.0 as starting...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
I'm trying to get the debug version dfu secure bootloader from nRF5SDK160098a08e2 running on a nrf52832.
I'm able to compile it using cmake and a gnu c compiler. However...
So I am doing a project with a 160x80 TFT display, using the ST7735 driver. I have slightly modified the ST7735 functions to work with my display, and everything is running...
I am trying to create an application which would send data once a minute. The application is based on BLE advertising packages, because it should be the most simple method...
Hi,Sir：
I am making a DEMO based on SDK15.0(SDK15.0\examples\ble_central\ble_app_hrs_c) and pca10056 for my one of important customs.I need to implement some extra software...
Hi,
I am now in Hong Kong, and trying to connect to NB-IoT network here. There are 2 providers of NB-IoT in Hong Kong: "CMHK" and "Three". They provide NB-IoT since 2017...
Hi!
I was testing the SD Card example that is available on the SDK 13.00 in the following path: "nRF5SDK1300/examples/peripheral/fatfs". I checked SDK 16.0 and the code...
I have a hard-to-reproduce bug in my MQTT application that I have investigated enough to realize that my MQTT thread is stuck in a call to mqtt_publish(). I've verified that...
I would like to add UART as an option to the "ble_app_hrs_rscs_relay" example in SDK16, But keep the peripheral low power.
i.e. once I set a GPIO, the UART will start to...
I'm working on a project where UART0 is used as a nrf logger uart back-end. Recently I've tried adding UARTE1 to the project to implement additional serial communications...
I am unable to initialize soft device, but I am able to initialize log, led, gpio and timer as well, I can see debug prints as well. After debugging I found following information...
Hi everyone,
We are developing switch product which running with Android Application.
We have problem about send status from switch Device to Android Application
+ Android...
Hi ,
I have tested two boarrds(PCA10040) with same application id and higher application version,These work well done.Then I want to test mesh DFU Relay function,However...
