I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
When I am going to program a custom board for the first time, can I use example codes from the SDK or should I change anything important on the configuration?
On my custom...
I'm trying to create a simple service that would just provide some data which could get updated internally (for example, via SPI bus). Data may be of a different size, so...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hi,
I'm just getting started and tried to run the lwm2m_client sample from the v1.2.0 release of the nRF Connect SDK which I assume is the latest stable version? However...
hai ,
in my apllication i am using nrf52840 , i merged a code code of peripheral and central (app_blinky example)
i need to connect a peripheral to central (with esp32...
I'm working with the nRF52840 PDK and I'm wondering how to change the PHY (preferably to CODED) in a Mesh. Has that been implemented yet? Or when can we expect this feature...
When developing the dfu upgrade device, the code can be loaded to 100%, but the prompt "remote dfu invalid crc error" The compiled firmware can be upgraded with the old nRFtoolbox...
Hello,
I'm trying to get the PCA10056 to communicate with the MPU6050 Motion Processor (I think that's what it's called), but still in the very starting point.
1 - I've...
I've been using STM32 controllers with LoRaWan mostly GNU based and bare metal. Recently, I have been looking at the STM Nucleo STMWB32 communicating with a Raspberry Pi and...
Hardware:
PCA10040
V 0.9.0
2015.47
Hello,
I connected the above development kit to my PC today and was prompted to update the J-Link firmware ("Strongly encouraged...
Hi,
I am using SDK16.0(ble_app_uart) program to sending dates between the phone and board.When I use my iphone xs max,it works on well.But it come out some faults when it...
I have a compile error currently: "section .heap overlaps absolute placed section .stack"
The heap size is currently set to zero.
I am guessing I am just going over the...
I keep getting this error code and while debugging I'm able to resume execution. This error seems to be thrown during my DMA transfers over SPI. Is there somewhere I can look...
I have a Thingy 91 and trying to connect it to nRF Cloud without any success so far. It is not connecting to GSM Network.
I updated both modem software and application...
