Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
Hi, does Nordic provide the "works with all hubs" Zigbee cluster?
I see this blogpost mentioning " Watch out for more information on future Zigbee 3.1 SDK All Hubs support...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Board: nRF52840
Hi, I'm a newbie in zigbee stack. I have been get started with the door lock example.
I want to make custom...
Just wanted to share how to interface a thermistor (103) with Nrf52840 and get the values over a BLE android app (Nordic toolbox). refer here,
github.com/.../Thermistor...
Just wanted to share the project for interfacing IR distance sensor with Nrf52840 and get the values over BLE app (Nordic toolbox)
github.com/.../distance-sensor-with-N...
Hi..
I am working nrf52832 with accelerometer sensor, I want to store the data about 100hz for 1sec in flash, I want to store it an array and send it over ble how to do...
- I used https://github.com/NordicSemiconductor/Android-BLE-Library version 2.1.1 and https://github.com/NordicSemiconductor/Android-Scanner-Compat-Library to code My Ble...
We plan to develop a temperature and humidity sensor based on nRF52832, which needs to evaluate power consumption to confirm battery selection.
are there any similar data...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
I'm trying to optimize an Azure project based on the Asset Tracker example. I was recommended setting CONFIG_SERIAL=n in both the Application FW and SPM. However when I add...
