Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
Hi there.
I am attempting to do some reallife tests on the nrf52840, mainly focusing on long-range capabilities and performance between the DK and an iPhone XS. Are there...
Hello, I've seen several posts about this, but I'm a little hesitant to use older posts since you guys put out new and improved versions pretty quickly. We are using SDK 16...
nRF52832 on a nRF52DK connectivity_4.1.1_1m_with_s132_5.1.0.hex pc_ble_driver_py v0.14.2
Steps to reproduce: - connect to a peer device - discover services and attributes...
hello :
1)The packet format of NRF52832 2.4G is as follows, I would like to ask whether the 2.4G CRC can be turned off.
I use two boards PTX and PRX to transmit each...
Hello fellow developers,
I'm developing the Bluetooth Low Energy (BLE) app with my own functions. Now I would like to pack it as a standalone Electron App, which can be...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
Hi,
I'm developing a BLE mesh project using Mesh SDK v4.2.0. I want to change the Tx power of the product in real-time, e.g. from 0dBm to 4dBm, 4dBm to 8dBm.
I've read...
I have an application that is running for a while and then it crashes.
Execution goes to softdevice_fault_handler(), calling it with parameters: id=1; pc=0xf764; info=NULL...
hi all
A silly question here , I am prepare to meet some security compliance , one of them is about delete files permanently.
I wonder how to get this done on nRF51822...
