Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
I have nRF52840 as the central and nRF52832 as the devices. I have the device names as TELCO_456, TELCO_457, TELCO_458 in the connectable advertisement packet. I have disabled...
I am trying to capture sniffer logs for a custom BLE peripheral using nRF51 dongle and Wireshark. I am following this guide here to install the Sniffer tool in Wireshark....
>I will start by prefacing that I'm not by any means an engineer and my only knowledge with BLE/embedded systems comes from curiosity, side projects and trial/error<
Story...
Hi,
I'm running of the fw-nrfconnect-nrf master branch (commit: 96e75dba598320c2707dede3ffef44bf326a89e3) because there are some improvements since the release of SDK v1...
Hi,
I am developing a custom device with nrf52840 and use SPI for flash driver and radar sensor.
For better SPI performance of the flash driver and radar sensor, I am...
As an example of this routine：
D:\Project\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs\ble_app_hids_mouse_pca10040_s132...
DK is not powering ON suddenly.
All the Power Switches are selecting properly (SW8 = ON, nRF Power source = VDD, SW6 = nRF ONLY)
USB is connected to J2 Connector.
Observations...
Has anyone been able to connect the nRF52 to MATLAB using their new Bluetooth Low Energy Communication interface ( https://www.mathworks.com/help/matlab/bluetooth-low-energy...
Why is "No location data available" always printed when SUPL data is downloaded in gps sample app? This happens at any place. I guess this causes a long TTFF.
This is a...
Hello. I have a DK nRF9160 0.8.2 version. I am sending AT command through UART with an external MCU (STM). I am interested on evaluating power consumption during an UDP packet...
Hello,
I am trying to integrate OPTIGA Trust X with the OpenThread example, "mqttsn_sleepy_subscriber"(from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 SDK). I tried adding...
Hello.
I am running Segger studio 4.5 on Windows 10 and the ble_app_uart example project that works fine with one connected central device (i.e. iPhone with nRF Toolbox...
