Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
Hello,
I'm having issues with what I believe are interrupts, if I use the bootloader.
I'll give a brief description of the issue I faced, and then I'll state how to reproduce...
Hello,
Is there any documentation available that specifies what version of nrfutil is required to create DFU packages which are compatible with a SDK and/or soft device...
Hi
I am using NRF52 with 512KB flash, and with SDK15.2
I am not using DFU
I tried to protect the program flash pages using "sd_flash_protect".
I tried to protect pages...
Hi everyone,
Currently I'm using Android Nrf Mesh Library 2.4.1 for provisioning device into network.
I face the issue which can not be found why to fix this error.
...
I cannot set CONFIG_POWER_OPTIMIZATION_ENABLE to yes in the master branch. It leads to deadlock in at_cmd_write() because that ends up getting executed in the socket_thread...
I copied the slm application into a directory outside the SDK (e.g. C:\temp\slmapp) and I launched a command prompt from the nRF Connect's tool chain manager. Then I navigated...
Hi, I was trying to interface nRF 52840 with a SPI based NOR flash (IS25LP064A). I am using SPI example in 16.0.0 sdk version. But i am not able to read the device id as this...
