hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Using SDK 15.2.0, s132, nRF52-DK.
The logging facility in Segger Embedded Studio tells me that the call to nrf_sdh_enable_request() takes about 500 ms. I have an interrupt...
Hi,
I was following your guide to implement a secure boot chain ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_bootloader.html ) and therefore build...
Hello,
I have a simple question. So, I'm trying to write some manufacturing information into the UICR but once I write to these addresses I can't see the device via bluetooth...
Hello,
I am using the UBLOX EVK-NINA-B406, which has the nrf52833. I have attempted to use Softdevice S140 and S113 (using the nrfConnect programmer. Soft device versions...
I want to interface the nRF5340-PDK board to a different vendor's board that runs at 3.3V.
I'm using the SPI bus to communicate between the two boards
Using the nRF5340...
I don't have absolute proof yet, but I'm 90% certain that the carrier LWM2M (0.8.1+build1) has a memory leak when used with a +CEREG notification level higher than it is expecting...
After much searching this site for a solution I'm at a point were I decided it necessary for me to ask directly.
SDK16.0, S132, windows 10 / SES, nrf52DK
I'm able to connect...
Hello, To contextualize my questions, here is my project : I am working on a mesh network with a proprietary protocol. Each node is stationary. I use the nRF52832 SoC.I use...
Hi everyone!
My simple question is: why does this page no longer available? https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google...
2020-06-08 16:20:39.229628+0530 OperationApp[3306:1831777] [Bearer] Central Manager state changed to .poweredOn
2020-06-08 16:20:39.635195+0530 OperationApp[3306:1831777...
How to add two or more custom characteristics in a custom service? I am able to add characteristics from github.com/.../nRF52-Bluetooth-Course to this tutorial. The same way...
Hello,
I want to start with BLE Mesh development. Therefore I have downloaded the Mesh SDK Version 4.1.0 from the Website and started to build everything. But I have a problem...
Hi I'm using the PCA10056 DK and ran into an issue. I can configure the nrf52 to wake up using input pins(although some pins can't wake it up for some reason), however, when...
Hi,
I looked at https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP/nrf52832/ic_rev_sdk_sd_comp_matrix.html and I was wondering if the nRF52832 rev 1 does...
I am using S112 6.0.0 / SDK 15.0.0 for nRF52810.
I decided to use an internal RC oscillator to reduce parts.
However, after changing the setting to LFRC, DTM does not...
