Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi, I am attempting to flash various bluetooth samples onto the nRF5340pdk, and I am getting errors on multiple levels.
First, when I attempt to build the samples (I have...
Hello, I am trying to load some example on my nRF52840 dongle. I am developing without using a board but only the dongle, SEGGER and nRF Connect 3.6.0 .
Following this guide...
Hi everyone,
I've noticed in SDK examples such as the ble_app_hrs that call APP_ERROR_HANDLER after softdevice API Call.
What is the reason for this API call?
Any side...
Hello,
I am working on ble_app_uart example on nRF52840DK.
According to the documentation, when the device is advertising, the LED1 should blink. But I am not able to...
Hi all,
I was going through the release notes of the S132 V7.2.0.
Under known issues, DRGN-10340 states the following:
"The BLE_GAP_EVT_SEC_INFO_REQUEST event will not...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see BLE library available for advertising.
I went through the ble_advertising_init API and found the parameter...
Hello, when I run OpenThread CLI example in NCS 1.4.0, I get the following message on the serial port:
E: Failed to store setting 3, ret -22
I am using the nrf52840 D...
I'm now using nrf52810 sdk16 for product development, but we need to pair bind. So pair bind, generate short-term and long-term keys where I can find it? How can I generate...
Hi everyone.
Not knowing exactly where to go to get help I am taking the liberty to ask my question here hoping that some good hearted soul might help me. The device manufacturer...
I created a project on nrf9160, which connects many peripherals, including SPI,I2C,UART. According to the specification, nrf9160 can use up to 4 sets of serial peripherals...
Getting the example programs to work from the NRF52 SDK can be a very daunting task. The big problem is that there is virtually no documentation included in the samples themselves...
Hi; I'm trying to develop an application with the nrf52840 as a co-processor. We decided to use the nrf52 as a SPI slave and a SAMD21 as a SPI master. I set up a quick Arduino...
Hi,
I have a question about the tolerance on the VDD voltage. In the datasheet it says: "RF 3GPP compliancy requires 3.3V."
I am wondering if there is more specific...
