I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
I am trying to setup L2CAP channel in ble_app_uart. I referred the object transfer example and did the initialization of L2CAP parameters during ble_stack_init() both...
For certification purposes to qualify for the QDID defined by Nordic , are there any characteristics that are required to be present in the Device information Service (System...
Dear nordic team,
I'm developing a sensor based on nrf52840 and I want to make use of CMSIS NN. I have already integrated CMSIS in my eclipse project and can already use...
Hi,
Here i am reading the temperature data via i2c protocol , where the temperature sensor is connected to the nrf52832 .(15.2 version sdk) Now i want to publish the temperature...
I'm using nrf52840 with nRF5_SDK_17.0.0_9d13099 and usbd_audio loopback example. The example works fine with the given hex file but when i compile it myself, the signal seems...
Hi :) ,
My project continues quiet well, and now come the time to create final assembli of all my small block.
I'm using nrf52833, with s113.
I want my device...
hi guys,
now i have 2 pieces 52832 boards; A(PERIPHERAL) and B(CENTRAL); both run the nus service.
B( CENTRAL)--->A(PERIPHERAL) Through ble_nus_c_string_send();
and...
Hi. I need the NRF52832 to work in two modes. After power-up, the radio module worked like a normal NRF24L02, and after pressing the button, the BLE started. I took the example...
Hi Team,
We are working on the nRF9160 DK. We are integrating the central_uart code into the lte_ble_gateway, As we integrated for the purpose to use NUS(nordic uart service...
Hi,
I am developping some kind of driver as my company calls it which will be used to easily setup a mesh network for our projects. I am using the light_switch_client_example...
Hi,
We are using nRF52840 Dongle to receive BLE peripheral Device 240 Bytes notifications for Win10 program. And w e used "pc-ble-driver-4.1.1\examples\heart_rate_collector...
Hello Nordic
I am working with nrf52832, sdk 16.0, softdevice s132
I need to advertise NON CONNECTABLE ble with changeable data (later relevant data will be received...
Hi
we are using the nRF52840 and antenna signal i connected ceramic chip antenna(ACAG020-2450-T).
The above attached schematic of ant signal matching circuit schematic...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
