Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Environment:
DSL-Router, IPv4 only, DHCPv6 disabled
Raspberry PI 3B, RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img, the raspberry is connected via wire with the dsl...
Hello,
I've been running some power measurements on our prototype board that is using the nRF9160. I've measured current draw on the VDD and the VDD_GPIO when the modem...
Hello ,
I am currently working on NRf52810 , SDK version 16 , I want to send around 400 bytes of data over BLE connection from peripheral to central. I know that NRF52810...
Hello, I am working for a BLE central application where the packets are send using L2CAP Connection-Oriented Channels. My development environment is based on nRF52 development...
I'm trying to get the ble_app_blinky example from the NRF5 Thread SDK working on the Adafruit Feather nRF52840 Sense using the S140 soft device v. 7.0.1 I'm compiling the...
I have a custom board with the NRF52832 chip. The supply is from a Lipo battery which after 3.6v varies from 3.6v to 2.5v. hence I have a varying input supply to NRF. Would...
Hi,
I am using TWI on a 52832 (sdk12.2) and am having problems with reading data. The slave chip that can take up to 60uS (8 bus clock cycles) between to set up data after...
Can the Nrf Mesh android app be expanded to support multiple networks?, i took a look at the android software , it uses MVVM architecture and uses Dao's and repositories to...
Hi,
I found that s113 SDK17,did not support +8dB TX power,could you please give me some suggestions ,when using nRF52820, which SoftDevice will support +8dB Tx power?Thanks...
Good afternoon,
We are carrying out a new project with your NRF52810 beacon to create a heat map of
movement inside a room.
Our questionis, do you have any software...
Hello,
I am currently running the openthread client example provided in the NCS and I am trying to toggle the client as a sleepy end device. However, in the toggle_minimal_sleepy_end_device...
Hi
I would like to know the availability of the open sources for the following:
1. BLE Gateway for PC, Android , iOS
2. nRF Cloud open source
Can you help, How to...
The nRF52840 UART example uses pins 1.13 and 1.14 for the TX and RX pins on the Dev Kit (uart_pca10056) and has a default baud rate of 115200, but the 1.13 and 1.14 pins are...
Hi! I'm having issues with inconsistent battery readout results. I'll elaborate more below, but in general, I have multiple devices which 'sleep' most of the time, and when...
