Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...
Hi,
I do have customized services in my project to implement,I think it would be easy if we seperate service related functions from main to add services in further.To serve...
Hello, There were some problems while making Bluetooth packet readers.
Packet sent to another device cannot be read in BLE_GAP_EVT_ADV_REPORT.
Is there any way I can read...
Hi. I'm working with the nrf52832 chip, and had a few high level questions I wanted outside opinions on
1) I have a lot of trouble connecting to my BLE device. I frequently...
Hi Team,
We are going to use the NRF52832 soc with S132 Soft Device and SDK Version is 16 for our project purpose, we have some queries on this soc along with these SD and...
Dear,
I am struggle a problem in mesh communication.
Mesh SDK 4.1.0
I used dimmer example.
Two nodes can communicate and work perfectly fine, only if they are in communication...
Hi,
I used DK board for quite a while with a single certificate, which has been generated and written by nrf_modem functions.
Recently I upgraded the modem to firmware...
Compiler error message: Development environment: keil5 DeviceFamilPack: v8.32.1 SDK: nRFSDK160098a08e2(v16.0.0) I can't compile successfully using the SDK example, how can...
Hello,
I would like to create a mesh application with different nodes that are gyroscopic and pressure sensor in a 10+- meters radius area and provide the data from the...
Hi
I'm working on a project in which I use a timer to generate two signals that I need to phase shift each other, but at the beginning and at the end it cuts, can anyone...
