to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
hello Nordic
i have s SOM which i want to use nrfutil in it for FDU via UART of an application i have on nrf52832, s132 v7.0.1
i have the bootloader flashed with the...
Up until now I have been the sole firmware developer and the keeper of the keys for our product.
Our scrappy little startup has expanded and is now bringing on additional...
Hi,
Problems I am having with PWM:
1. Using app_PWM and GPIOTE to start and stop the PWM: When button is pressed, GPIOTE handler sets a flag that is polled to start the...
I am using Timer0 and Timer with GPIOTE and PPI to output 2 clocks on 2 pins.
Both timer settings are identical (for troubleshooting). Only timer-0 can be generated at the...
I am working with nRF Connect SDK using an nRF52840 DK. And I want to realise both BLE mesh and FOTA upgrade. FOTA upgrade example SMP Server Sample works properly for Bluetooth...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
I am using 2 counters, one to produce the 4MHz, and the other for the 62.5KHz, to drive I2S module.
I need to find a way to stop the first counter (4MHz) after it produces...
Hi All,
Currently I am using SDK_17.0.0 for nRF52832 with Softdevice S132_V7.0.1. I come to know about release of SDK_17.0.2 with highly recommendation to migrate from SDK_17...
