How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
I'm looking at the UICR hardware peripheral example , and trying to figure out the utility in writing to the UICR registers.
Why would I want to modify the compiled hex...
Very new, so please forgive the questions, but...
I have an nrf8001 that I've powered up. After initial power up, I'm able to read the DeviceStartedEvent but the response...
I'm looking to integrate a digital (PDM/I2S) MEMS microphone into my nRF51822-based design. I'd like some pointers to reference designs or other information -- the ones that...
Hi,
I would to know why when the DC/DC is enabled the current is very high (57mA) during RF sending.
Why at the end of RF sending the current is higher than...
I am modifying the bootloader. I am not using DFU or any of that, but rather copying a FW image over from external flash through SPI. The area of my code that gives me problems...
The documentation of the S110 contains sequence charts that explain how the different GATT operations are performed.
developer.nordicsemi.com/.../a00885.html
It seems...
Hi,
I've been trying to do fake non-connectable advertising with a nRF24LE1 with base on [1] and [2], they use nRF24L01+ with an AVR which I have ported to my device. I...
Hey,
I'm evaluating a nRF51-DK and face NRF_ERROR_INVALID_ADDR when trying to set a value in the local gatt server database.
My goal is to create a read-only characteristic...
Hi,
I'm using nRF51822 Beacon v1.1.0. Is it possible to detect that the beacon is being scanned? Is there any event generated during this process that I can catch?
I have been studying the ble_app_hrs example, but it has unnecessary functionalities, and it is hard to understand.
Do you have a simple application for transferring data...
I would like to use that chip with appropriate codec as wireles Tx/Rx set. I need of uncompressed audio signal and my sours will be analogue amplifier and the Rx module has...
Hello there,
I am using multilink_central example on nrf51822 Soc, and I charged S120 in the memory. I am trying to get the RSSI and the MAC address without getting connected...
I am trying to get the sniffer to run and having problems. Tried both 0.9.7 and 1.0.1 same results on both. OS is W7-32 home. Hardware, have tried several PCA10000 and a PCA10001...
Hello community, I have the uVision 4 installed, I tried to open the project to compile ble_app_hrs_dfu but get the following error.
I find this file in C:\Keil\C51...
