I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
Hi!
I started to modify the ble_app_blinky example. I need to increase ATT_MTU, so I modified NRF_SDH_BLE_GATT_MAX_MTU_SIZE. For this, I needed to increase the RAM of the...
Hello,
I'm using Mesh SDk4.0.0 and SD v7.0.1. I have tested the light switch client and server examples.
Now I want to add some more models for additional functionality...
Hi , i want to change the device name by connecting the device using nrf_toolbox , have a look at my code , you will get what i am trying to do . By the way i am using nRF52832...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0, gcc-arm-none-eabi-7-2018-q2 in my customboard.
Recently, I am making ble central module.
I can scan and...
Hi, I have only one question: during the write or erase cycle using fstorage, the cpu is locked? Sofdevice, Interrupts and main application are working also during with flash...
I'm using FDS together with Flash manager, and checked if everything goes alright in flash.
As per doc, I set FLASH_MANAGER_RECOVERY_PAGE_OFFSET_PAGES to FDS_PHY_PAGES....
Hi, I just try to start with the spi master example (nrf5sdk/examples/peripheral/spi) on mus PCA10040 board. I'm able to compile&flash it. It seems to be running (LED1 is...
Hi ,
I working on the getting started assistant setup but got failure when verify the GNU ARM embedded setup , see the following log :
11:32:05.867
c:\gnuarmemb\bin...
Hi,
Just want to ask what will be the effect if I will use an external oscillator (32.768kHz) with a CL nearly at max specification, let's say 12pF.
Thanks.
Hi,
Can we send a message from a Provisioner to a Unicast address in a mesh network?
I'm using nrf52832 and can send orreceive message between nodes in the mesh but I...
Using 4-bit SPI mode on the Display Controller side: SCL,MOSI,MISO ... and DCX (by which the controller distinguishes between command bytes and data bytes). There's no obvious...
