Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I have compiled my mbed program and hex file has been downloaded but I am unable to drag and drop my hex file to mbed USB drive. It is saying Not Ejected properly. I tried...
I am following app note nAN-29 "nRF51 Development with GCC and Eclipse Application Note v1.1". In the section "Flash download" there is mention of an executable called nrfjprog...
Hi
I use the PORT EVENT to produce multiple interrupts.But I have a question by these:
NRF_GPIO->PIN_CNF[BUTTON1] =
(GPIO_PIN_CNF_SENSE_Low << GPIO_PIN_CNF_SENSE_Pos...
Hi,
have some of you expierence with profiling on a nrf51422? I think what would be nessesary, is at least one high priority timer, to sample the program counter, some kind...
Hi,
I’ trying to save some user configuration data on the NRF51822 Flash using pstorage module.
Below is the code that I wrote, the code runs on the board with no error...
I have two boards based on nRF51822 parts:
Nordic dev kit PCA10005 Rev 2.2.0 2014.14, chip marked N51822-QFAAG0-1351AG
Custom board with Fujitsu MBH7BLZ02-109004...
I'm getting an error which says the identifier ble_temperature_t is undefined, and it is showing as an error in the keil (unkown type name). However when I click on the variable...
Hi everybody,
I just received the nRF51822 EK and as I was starting to set it up I ran into this. It took me a while to figure it out but when trying lo load the blinky...
Hello,
I have problems with project making since I started with KEIL uVision 5 (in uVision 4 I had no problems, but see no way to download uVision 4 any more).
I followed...
I am not seeing the nRF51822 as an option when I go to select a target device in Keil µVision.
From reading questions on here I understand that the nRF51 SDK should include...
Hello,
I'm new to the nRF51 modules and I just started with nRF51422 module.
I have Keil uVision v5.11.1.0 with MDK Pro v5.11.0.
I have installed nRF SDK - nrf51_sdk_v5_2_0_39364...
Last time I used Keil µvision4 few weeks ago everything was working fine,
Today I got first a connection problem with keil µvision4 when trying to upload some code, then...
