But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
Can I get suggestions on how to implement the following topology with respect to provisioning:
There are a series of lights and each of them is connected to a central...
I want to write a data stream coming over UART into flash memory of the nrf52840 & echo it back after writing it to flash .
Please suggest from where i can start ?
Thanks...
Hi,
I was trying to create bond between my Android app and the device. At the beginning it worked well, and later I erased the board to start over. But then my app would...
I'm migrating an existing application from SDK v13 to SDK v15 and have run into a minor issue with the fstorage changes introduced in SDK v14.
My application uses both fds...
Hello,
I'm using Eclipse as my IDE to program the NRF52833DK with zephyr OS project . I build and flash the sample program blinky_pwm .
But I'm not able to debug the soft...
Hey all! So I'm working on some custom boards using the nRF52810-CAAA chip, I write firmware using SDK V15.2.0 (outdated I know). I'm having an issue with a recent batch of...
I've been struggling to track down excessive power consumption on a nRF9160 device and have found that, when all UART/Serial are de-selected/off, adding or commenting out...
I want to modify the asset tracker application, for that I copied the 'asset tracker' folder from 'ncs/v1.4.0/nrf/applications' to a folder outside the ncs directory. Then...
I am trying to add a characteristic and am getting error 7 (invalid param). I started out calling sd_ble_gatts_characteristic_add() directly but I realized that characteristic_add...
Problem:
I am trying send samples from SAADC to the NRFconnect app at 1kHz. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . I have...
Chip: nRF52832
SDK: 15.0.0
SoftDevice: S132 6.0.0
IDE: IAR EWARM 8.30
I have a peripheral-role application with __ICFEDIT_size_cstack__ = 0x800 (application call stack...
