We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I am starting development on my project using the ble_app_hrs as a template. This project already has the buttons setup for interrupts using the Button Handler library...
Hi guys
I use gazell protocol for my application. I want to try some other way to decide the channel tables. So I decided to monitor the RSSI and chose the channels in...
Hello, I want to be able to perform actions in my app based on the tactile buttons being pressed on the beacon. When I bought it I was under the impression that the service...
Hi,
I have some problems to advertise a custom 128bit UUID.
I succeeded to set the 128bit base UUID and my Characteristics UUIDs are 128bits.
But how I can set the PrimaryService...
Hello,
I want to implement device pairing, using the pairing bit. The pairing bit is set in the masters device type. For a slave to pair with such master, it opens a channel...
Hi Nordic!
I am using nRF UART2.0 and nRF51822.
I am sending some data from nRF51822 to nRF UART2.0
But after 3 minutes, I can get disconnection.
and 0x16 error...
I am currently using ARM's CMSIS-DAP interface to support flashing of an nRF51422 from a host MCU (i.e. to perform updates of the SoftDevice and/or application code running...
Hi guys,
I have a custom hardware with the nrf51822 and we have a slow connection and services discovery is clearly slower that when we run the code in the Development...
I use two nRF24LE1s as transmiter and receiver Here are my questions:
I set the transmiter side to auto reply mode using PIPE0 ,but i found the STATUS regesitor to...
Hi I am trying coding a remote controller using nrf24le1 but failed. any sample code?
it with several keys when push down the pin will connect to GND.
when any key push...
Hi all,
I would connect the NRF8001 module to my microcontroller (SAM3SD8C). Does anyone have an example code for this microcontroller?
Otherwise is possible to modify...
Hi All,
We have a PCA10001 running a ble_app_hid_mouse (modified according to our use case) which receives data from PC UART.
We are trying to connect to this device...
I cannot find any instructions on how to "pair" the nRF8001 with a laptop (I understand that BLE doesn't pair like usual BT).
Are there any tutorials available?!
Thank...
I am trying learn how to handle a central when the bond has been deleted on the device only.
It is a HID device using softdevice7 / sdk6.1, with max 1 bonded centrals....
