i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
Dear,nordic:
Please help me solve the exception encountered during the MQTT connection
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hello everyone a basic question but just to be sure.
I would like to make a custom board and I want to program this board with segger Embedded studio, should I just have...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
It was my idea to compile the mqtt_simple vom v1.3.0.
I spend now one week with your sdk. I tried it with SES and also with command line. Absolutly nothing worked.
The...
I am using a nRF52840-PCA10059 dongle to acquire data at a high rate (between 50Hz and 400Hz).
The connection is very unstable, after some seconds of acquisition, it sort...
We recently bought four 'nRF 52840' dk boards, and are trying to do board to board (non-mesh but single) wireless connection. However, there are just documents of mesh-communication...
Hi all,
I'm running into trouble using openocd to flash code onto the nrf52840 and then step through it. I'm running High Sierra (although I doubt that's important), and...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to picture.) Which Interface...
I have developed an app with DFU using SD s112(version 5) for custom NRF52810 board.
Q1: I want to update SD s112 to version 7. is it possible ?
Q2: how ?
Hello,
I'd like to detect a power failure and keep the nRF52840 alive using for example a super capacitor.
From the hardware side, is it ok to just feed the nRF52840 through...
I am a newbie for BLE MESH. Trying to migrate the existing product which based on self-defined GATT service to BLE MESH network, and got confused.
Current scenerio, the...
Hi.
I am using nRF52840 as a USB mass storage device with SD card. I came across the docs stating that the total number of BULK endpoints available are 14 (7 IN, 7 OUT)...
