When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
I would like to understand the timeout values for wait for acknowledge on ESB protocol
Example, from the source code:
#define RX_WAIT_FOR_ACK_TIMEOUT_US_1MBPS (73) /*...
Hi,
I'm a firmware eng with an ancient history of h/w design.
We are in production with the nrf52840 but still do new designs.
This question is in reference to the 52840...
Hi, We were trying with a new n/w carrier in Canada ( Maxim ). nrf9160 is able to connect to the network, but it is not able to resolve our server URL ipv4 address. Below...
Hi,
I am testing RX mode.
And the module is sure to enable M1 (%XSYSTEMMODE: 1,0,0,0)
I use the following command, but return error.
AT%XRFTEST=1,1,2,19500,17,1,0...
Hello,
I´m writing my thesis and using the Online Power Profiler to get a estimation about current consumption in NB-IoT cases.
I would like to use the diagram from the...
Hi, I have developed zigbee stack.
I tested to connect the door lock example of Thread and Zigbee SDK 3.2.0 with ZC of SDK 4.2.0.
I checked connection with these.
So...
Hi,
We are going to use NRF52832 for a project, and planning to design our own PCB card and assemble the NRF52832 chips, purchased through Digikey or a similar distributor...
Hi everyone,
I have designed a project based on the Radio test example, in the Nordic SDK. After programming all my code on the NRF52833 DK (PCA10100), i decided to design...
Hello, I have 4 NRF51822 modules, 2 stlink programmers, and a BLE400 board, I was using the same module with the same stlink each time, but the led on the board stopped lighting...
Hi,
I am going to transmit and receive data with libuarte. I read the libuarte example, but I am not quite sure my understanding of the data transfer process is correct...
Hello
I am trying to configure the spis with the nrfx drivers. My code is as follows:
I enabled the nrfx SPIS driver and the nrfx SPIS3 instance via Segger Embedded...
Dear,
I want copy antenna design from PCA10040 for BLE. Could you please help to provide antenna's spec, such as gain, efficiency, Radiation Pattern?
Thank you.
We are trying to program the nRF5340 via SWD from a host MCU and would like to understand if there is a white paper/blog post similar to this one:
https://devzone.nordicsemi...
Hi, Currently, we work on a project that uses: nRF9160 Zyphre OS Segger Embedded Studio for Arm (Nordic Edition) V5.10d SDK v1.4
This is our situation.
We want to measure...
