Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hello!
I am having a problem using any internal flash writing libraries. If I set the REG0 voltage to 2.7V, the controller stops erasing the memory.
Moreover, I cant erase...
Hi,
I have seen that the pin for nRESET is selected on the NRF_UICR->PSELRESET register. I know that it cannot be modified from 0.21 on the 52832.
Can it be modified on...
Hi guys,
I am trying to figure out how to send the sensed data (temperature value) from the LPN node to the server node in the BLE mesh network. I have already found this...
I am using the nrf5340PDK and i am trying to have P1.04 trigger an interrupt on a high to low transition.
attached is my overlay file and my main.c to initialize the GPIO...
I made a code based on ble_app_uart_c which connects to a peripheral and once connected it can write or read data.
The code is supporting BLE4 (1M) and BLE5 (Long Range...
Dear Concern,
we have tried to configure the accelerometer LSM6DSO module through SPI interface using NRF52xx DK board. External Module was not configured properly...
Since the Online Power Profiler only supports 1M PHY, does a static power profile for coded PHY exist that shows the current levels for the full advertising length? I'd like...
hi
nRF5 SDK for Thread and Zigbee v4.1.0
need to build a simple sensor with analog input .
Referring to the simple sensor (binary input ), I did make a ZED simple binary...
i made a mesh network using cli ftd uart example and transfer data using udp portal
there comes a need for me to indicate reset command through switch and send reset command...
I have 2 devices connected, working in notification mode. Using the nRF Sniffer for Bluetooth LE I was able to check all the messages that are exchanged. When in close proximity...
Hi, We have chosen to put our project and "custom board" outside of the NCS-directory. And since the newer revisions of SES, the "Open nRF Connect SDK Project" dialog window...
Hi,
On the P eripheral , after establishing a connection with the Central , start the timer to send data to the Central (the timer interval is set to 500ms and stop after...
I'm trying to get Thingy91 works under either Mac OS or Linux. Neither of Programmer nor LTE Link Monitor doesn't work. Programmer complains about that device is not in MCU...
