But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I updated Segger Embedded Studio to the latest version, 4.50, after that it asked me to update JLINKv6.62a firmware update, but there after I had problems with the board...
Cortex M33 applications on the Thingy-91 - are we able to write any application program that would normally run on a standard M33 ARM processor (off the shelf) - or are there...
Hi I m new to Nordic products and I m just evaluating the nrf5340-PDK.
is it possible to enter in SYSTEM OFF and wake up the CPU with RTC0 or RTC1 interrupt?
How To do...
Hello to all. Is it possible to send and receive data between 52840 dongles using ZigBee? I need a simple program which records data in one dongle and sends to another. Thanks...
Hi :
Our project(SDK15.2) use the uart DFU to transfer the firmware , usually when the firmware has been transfered ,it can jump to app successfull .But Sometimes,bootloader...
My goal is based on SDK16.0.0 and s132_7.0.1 softdevice to achieve BLE DFU (requires binding) and UART DFU work at the same time, I have combined the 'secure_bootloader_uart...
I am having an issue using the DTM app in nRF Connect. It is the latest version of the app (v3.3.0 as of this writing). The issue is that if I disconnect the debug lines ...
#define FIRST_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(20000) //20s
/**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update...
Hi,
So I am currently trying to connect my nrf52840 DK to aws cloud using an LTE modem. My aim is to be able to store responses from the modem and parse them appropriately...
I have a simple question.
I am successfully reading an external ICM module and I am trying to print is identity (value 0xEA).
NRF_LOG_INFO work perfectly well on the...
Hi ,
Have a problem,pls help
Software: nRF5_SDK_15.3.0 (ble_app_hrs_freertos)
Hardware: nRF52832
In the User Appication Code,Using CRITICAL_REGION_ENTER()/EXIT(...
Hi,
I use nrf52840, I meet some problems about the USBD, Can you help me?
We know that the usb device send data to host(such as PC) by EPIN：
(1) The host send IN event...
I am trying to setup NRF Sniffer for 802.15.4 using nordic board PCA10056. When the capture is started on Wireshark, the capture starts but the sniffer doesn't seem to capture...
Dear Nordic:
I pretend to develop a tool to search all surrounding Ant+ sensors and list them. User can choose target sensor then he can see the sensor data.
I expect...
Hi all,
We are currently working on an application that uses the timeslot API, and requests timeslots spaced 20ms apart.
In our application we need to trigger some functions...
