Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Given the info here and here ...
1. Does this mean that the nordic example here is wrong, and that line 54 should be time_struct. tm_mon = month - 1; to account for the...
I use SEGGER build mesh V4.1 project light_ctl and light_switch.
I flash light_switch_server_nrf52840_xxAA_s140_7.0.1.hex and light_lc_server_nrf52840_xxAA_s140_7.0.1.hex...
Hello Nordic
I am using nrf52832, skd 16.0 , s132 v7, the data with the new FW will be delivered via UART
I wish to understand some issues regarding FW update, after doing...
Hello,
I am working on SDK v14 version mpu6050 sensor. I found an example of mpu6050 here.
https://github.com/Martinsbl/nrf5-mpu-examples
And here I found a way to...
Hi, I am working on nRF52840. I want to add Device Information Service in ble_app_template. (as shown in the attached image its from another device) How can I add? Kindly...
Hello,
nRF52840, SDk16.0, Softdevice 7.0.1,
I am having the following flash write error message while writing data to flash. I'm using FDS library. Interestingly this...
Hi, I am following the below link for creating custom services/characteristics. https://github.com/bjornspockeli/nRF52-Bluetooth-Course
I have set the device name as...
Hi
based on nus example , I'd like to create RX/TX characteristics with a custom UUID (128bits)
My problem is about the UUID characteristics versus UUID service, for example...
I've inherited a project where the software was developed in IAR and I've rebuilt it in SES. I am having an issue configuring the memory for the soft device.
The chip is...
For a project under development I used two NRF24L01 for testing and they work very well.
Now I would like to know if: is it possible to use one NRF24L01 as TX and several...
Hi, I am working on ble_app_template. I am trying to save a value in the flash memory of nRF52840. I am using the following 2 functions to write/read in flash memory but getting...
Hi everyone
I am using app_uart_put() method for sending data via UART. The problem is that when I send each byte I get each byte back to its event handler in APP_UART_DATA_READY...
I have a Thingy:91 connected to a Garmin LIDAR Lite v4 (built on the nRF52840) via four GPIO cables. The code running on the Garmin reads one GPIO pin to signal a measurement...
