I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Using ble_app_hrs running on a PCA10004 (nRF6310 motherboard + PCA10004 which uses a PCB antenna), the achieved range at +4dbm (<10m) seems to be short. Master Control Panel...
I think the new MCP might have a bug somewhere. I have not been able to find out the exact sequence on how to provoke it, but I have to restart the application more often...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
Hi,
I disconnect the BLE by calling *sd_ble_gap_disconnect*(), and found that it run to *app_error_handler*() after the BLE_GAP_EVT_DISCONNECTED event occured, and I don...
I program the nRF2727 module with the "Block readback of mainmemory" seleted using nRFgo studio tool.
After that, I can still read out the content of flash. What's the root...
As per this thread: devzone.nordicsemi.com/.../question-regarding-hfclk-control the SD stack takes care of HFCLK, however as fas as I understand HFCLK is also responsible...
Hi,
I use the DTM for the production test, I use the transmitter test ,with canal 19 (frequency = 2438MHz).
What is the tolerance of the frequency do you recommend (Min...
Hi all
i am working on Student Response System in which there multiple Transmitter and one Receiver and i want Receiver(nRF24lu1p) to behave as HID device.
Can any one provide...
I just buy a set of nRFgo starter kit . One pin of the display module (nRF6350) was destoryed, and the correspoding hole of P6 in the motherboard was inserted with short pin...
Hi,
I have some questions about how BLE scanning works that haven't been answered clearly anywhere I can find, (except no-doubt the Bluetooth Spec/Tome):
What...
You can not build out " the arm c c + + compiler has stopped working " in Keil uVision5.
PC of lenovo made in (Windows7 environment ) ,
By introducing development environment...
Hello everyone,
thx in advance for answers.
there is limitation written for 6.0.0 as follows:
Synthesized low frequency clock source is not tested or intended for use...
