Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
I have a custom PCB and i have connected the MISO,MOSI,SCK,REQN and RDYN line from the nRF 8001 to Arduino. And uploaded your code of ble_uart_project.ino but nRF 8001 does...
Executing:
nrf_gpio_range_cfg_input(0, 39, NRF_GPIO_PIN_NOPULL);
I believe it will.
I know the range should end at 30 but I hit the wrong key when I coded it. So...
I have a characteristic that is 80bytes long which is sometimes read by the client using long read. I also want to send the complete attribute value when its state changes...
Hi guys,
i tried to find information about the differences in chip revision
nRF51822-QFAA-R7, NRF51822-QFAA-T and nRF51822-QFAA-G0 but i can't find the R7 or T type anywhere...
1.
Are there any other resources than RTC/WDT requiring 32kHz LFCLK, not listed in Table 28 of nRF51422 PS (i.e. Radio)?
2.
ANT stack requires LFCLK +-50ppm, so +-25ppm...
Hello,
I'm getting an exception while starting MasterEmulator Sample Programs. All indicated Dlls were copied along with .exe, windows ver is 7. the same error happens...
Hello all,
I would like to send Acc and gyro data just like health temperature over nRF8001. Which Service can I use? How can I create one?
Thanks for help in advance...
I have BLE Shield V2.0 and i want to change the device name from the iPhone. We can use nRFGO Studio to change the name from GAP Settings but this is only one time change...
When using proprietary radio protocols only (Shockburst/Gazell) are there any difference between nRF514 and nRF518 chips? Do they behave totally equal so they can be used...
I need to send a data package when radio is ON every time
but I try to send data by "sd_ble_gatts_hvx()" I find it can not work,it seems that I can't call this API to send...
Hi
i'm new in dev zone and i have a question
now i work with nRF8001 and i want to design a pcb for it.
I want to reduce the BOM and for this i want to use only the internal...
Hi,
I am trying to use the DFU example provided in SDK 5.1.0. I have built the example using gcc 4.7.x, and i am also using softdevices 5.2.1. The DFU example has been...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
