I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I have a multi peripheral sample I am trying to make work
I do a
BLE_NUS_DEF(m_nus) and BLE_HRS_DEF(m_hrs)
this will register two event handlers.
When an event occurs...
I have downloaded nRF5_SDK_12.2.0_f012efa and tried to test logging in examples but without success. Even if I compile an example where NRF_LOG_BACKEND_SERIAL_USES_UART 1...
Hi,
I'm trying to use an nRF52840 Dongle to make measurements from 4 SMT172 temperature sensors.
I developed a proof of concept on an nRF52840 DK, where I connect all...
Hi,
Finally i am able to build a basic TCP/IP server client, attaching the project here , i have some questions wrt modem and TCP/IP stack:
I see two different socket...
Hi,
I'm trying to increase Zigbee Tx Power to +8dBm by using the function nrf_802154_tx_power_set().
Digging into the code, I see that it is calling nrf_802154_pib_tx_power_set...
Hi,
I am using NCS 1.2 with Zephyr SMP_SVR example compiling with my own board DTS and using MCUBOOT
I have my own partitions configured in my DTS (attached down at the...
So I'm trying to start off development of my project using the PCA10040 development board. I have downloaded the SDK16 and built a couple of examples no problem using SES...
Hi,
I have a question regarding the frequency of the SPI peripheral of the nrf52.
According to the Product Specification v1.4, the minimum value for the frequency is 125kbps...
Hello Nordic Support!
The stop bit of the last character is short in the Uart output part, and the other MPUy cannot receive the character. How do I fix it until I send...
To the kind attention of Nordic support team,
I was wondering if it is mandatory that Host and Devices share the very same frequency table, with same size.
Is it possible...
Hello,
Because I have no space for additional transistors on my board I made a design with nrF52840 and rgb led connected to 5V.
Configuration o GPIO pins:
H0D1 Value...
I was wondering if I could get some guidance with regards to the effect of interrupting the nRF9160 GPS during an initial cold fix.
Consider an application which uses...
Hi, what is the accuracy of the humidity sensor of the nRF52 at low relative humidity levels (<10%)? Checking if I can trust the numbers I see in a nitrogen glovebag. Thank...
Hello ,
I am having requirement to use the mesh network with 50-60 nodes and they will be operated with one server. could you please suggest and help for the product.
