Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
Hello,
lately i've not been able to connect to NB-IoT network as i did before.
Long story short:
I'm working with nrf9160 since 3 months and i have been able to connect...
When the macro NRF_SDH_BLE_GATT_MAX_MTU_SIZE is changed in the sdk_config.h file of any example from the ble_peripheral folder, the slave sends the message Exchange MTU Request...
Hi,
I am using nrf mesh sdk 3.1.0. with nrf52832.
For iv update one condition is iv_timeout_limit_passed(m_net_state.iv_update.timeout_counter). The timeout_counter value...
Hi,
I am evaluating ble peripheral with nRF52840 SDK 16 and SoftDevice s140 on windows 10.
The SDK is copied at location: C:\Nordic_Semi\nRF5SDK160098a08e2\
The SoftDEvice...
Hello,
I am not able to connect the dots. After setting up the beacons, ( adopted ble_beacon_app from Sdk 16 ) how can I perform localization algorithm ( trilateration)...
Hello. I try to configure radio at NRF52811 to prepare antenna switching and get correct I/Q samples from different antennas. I have 2 antennas that are 6 cm apart from one...
hello, I try to make an application with 6 different services. I used the ble_custom_service tutorial to create my different services.
I manage to work without problems...
Hi,
I am working with the bsp.c functions. One of the actions is BSP_BUTTON_ACTION_PUSH, which the value is 1. I would like to know at which electrical signal it is related...
Hello All, I am having a trouble with the nReset Pin during Deep Sleep. The issue is that the board is waking up from Deep Sleep due to floating nReset Pin. I am using a nrf52480...
Hi,
I am currently working on a product based on an nRF52832 (SDK 15.3, S112 6.1).
The firmware uses the Nordic UART Service to receive and send data from and to a smartphone...
I'm working on a new nRF5340 project where this will be the main application processor. The target system will support a large variety of sensors, and we expect to use a very...
Dear All,
We have designed our custom board based on BMD-330 (nRF52810 chipset). It uses i2c (TWI) to communicate with Azoteq IQS620A sensor .
TWI code runs fine on nRF52...
Hello there. I have few questions about nrf9160 GNSS part. Seems NRF have implemented own GPS L1 C/A correlator, current quality is not impressive at this moment, but approach...
Hello
In the radio test we can set up to 80 channels.
But isn't the table for the channel as follows?
40 channels is 2480MHz, right? What is the frequency of 80...
