I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am migrating to the Fanstel BT840XE module with nRF52840 and a Skyworks PA/LNA. I need some assistance in getting my PA/LNA working in a multiprotocol setup.
I have successfully...
I have application developed that works ok on nRF52 DK (nRF52832) with S112 and now want to migrate it to a custom board with nRF52840.
Could you confirm that S113 is...
Hi:
Since we have a issue that when nRF52840 setting to DCDC mode, our inductive touch will have bigger noise, if setting to LDO mode, the inductive touch noise disappear...
Hi,
I've been trying any way I can think of to work around an issue "51" returned by nrfjprog executed from nrfutil when trying to run serwer from the steps in tutorial...
Hi experts
i am using nRF Sniffer to decrypt the BT Mesh packets with Wireshark, it can work smoothly. However, i tested and found that the packets device key encrypted...
Hello, I am looking at the mesh dfu example code on nRF mesh SDK-4.2.0 on an dk_nrf52840 and I have some questions.
Rather than having both a bootloader and main application...
Hello.
We are developing products using BLE modules.
The one used for that module was "nRF52832 (512kB Flash, 64kB RAM)".
I would like to know
Question 1:
As a...
hi ,
I am working on the nRF52832 , I am trying to store the values in structure and then passing over BLE . I am getting this error after print statement unknown function...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
To setup the UARTE for use in Zephyr I've configured a nrf52840dk_nrf52840.overlay as Zephyr documentation suggests:
& uart1 {
compatible = "nordic,nrf-uarte"...
Hi, I'm setting up a timer to invoke (via PPI) the ADC in scan mode. It'll read to channels with MAXCNT of 10,000. The ADC built in timer has a value from
[80..2047...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
