After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
I'm chasing a bug and narrowed it down to a minimal failing case. Even it's only very few lines, I'm still failing to grasp what's actually happening.
Taking the...
Hey guys,
I'm working with SES, nRF52832 and SDK14.2.0.
I have a timing problem and would like to describe the problem from the beginning.
I have a 1-wire temperature...
Hi.
I'm having Segfault issues with our company's custom boards based on nRF52840 chips.
I do several re-flashing with J-Link EDU Mini Programmer on a daily basis with...
Hello, I am reporting here an issue that I detected by using NRF connect on iOS (cf https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/56 ) The issue is that the...
Hi,
I use SES IDE, nRF5_SDK_16.0.0, nRF52840 DKs. I am using ble_app_uart_c as a template for my application that needs to connect to multiple peripherals whose device names...
HI All,
Using Nordic devices and with my mobile I am able to do bounding and pairing.
But, after that, I have deleated the bounding information from Mobile.
Now, If...
Hi all,
I am trying add Long range to NRF52811 (app_uart_nus and app_uart_nus_c) in SDK 15.3
I checked this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hello,
About RTC module, Systick and SoftDevice.
Does SoftDevice make use of RTC module events ?
Does SD also make use of ARM SYSTICK ?
Note : we do not use FreeRTOS...
I have implement an in-app DFU procedure based on Nordic's dfu ble service. The images are saved into external norflash and then control is passed to a bootloader which validates...
Hi
This is my code for antenna switching. I've got 8 antennas I want to switch between.
NRF_RADIO->PSEL.DFEGPIO[0] = 0x00000011; //(P0.17) NRF_RADIO->PSEL.DFEGPIO[1] ...
I am using nRF52832 on my device. I have used SDK13 and softdevice 4.0.5.
On any iOS devices I can scan and connect in the nRFConnect app.
On an older Samsung Galaxy S5...
Hello,
we need some advice to choose the right TX power. We still wonder if TX power +4dBm is the best choice or better use the default 0dBm.
Here is some background...
Hi,
We are working NRF52832, SDK15.3. It works properly in debug mode but when I build in Release mode it is not working.
From my understanding debug mode will have symbols...
i use the demo ble_app_uart ，and i want to close the uart when ble is "Disconnected"。
but it when it do app_uart_close(),the nrf52810 is RST。 i use the same code in nrf51822...
In the nRF52840 do the peripheral interrupts (e.g. UART ENDRX) set the event register in the ARM core? If so is __SEV(); __WFE(); the only way to clear this event?
