I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hi Team,
We are using nRF9160 DK. In the process of testing I would like to know that is it possible to send data from nRF cloud to nRF9160(LTE device). I have gone through...
I'm using SDK 16.0 with SD340 6.1.1 on nRF52840
I'm working through alternating advertising on coded phy and non-coded phy. I have two scenarios where I don't want connections...
Hello Nordic team,
I'm looking into solution to pass data to my application after a Reset using the RAM of my nrf52840.
Looking at the documentation, this picture troubles...
Hi,
I have a question regarding BLE timeslotting. In my setup I have a master with multiple slaves and equal connection intervals set at 7.5ms. The slaves acquire data that...
Hi,
I am using nRF52 to complement BLE function of MTK7628(they communicate through UART),I've implemented most of the functions.Now I want to add OTA to nRF52, so I use...
I'm trying to combine these 2 examples. I tried adding the uart code:
uint8_t cr;
while (app_uart_get(&cr) != NRF_SUCCESS);
to apps_ble_uart while loop and the whole...
Hi all,
I´m trying to create my first BLE application with segger embedded Studio.
My Hardware is the nRF52833 DK with a sensor connected to dev Board via I2C lines...
Hi, there in inconsistent data about the number of UARTs in the nRF5340 OPS v0.5.1:
- Page ii (nRF5340 features) states "Up to 2x UART (CTS/RTS) with EasyDMA" for the application...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...