When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello !!
We are using nRF52833 MCU in our one of project. It is very cost sensitive project. We are proving supply to MCU from coin cell CR2032 battery. Also we enabled...
Hi,
I'm currently developing custom board with nRF52832 and I'm experiencing weird issues.
It's mostly related to BLE, especially on Samsung A series devices (A3, A7,...
I am using custom board nRF52820. I'd done OTA up-gradation with USB connected. Firmware successfully updated on device over BLE and device got soft reset.
After removal...
I am using nRF9160 DK(PCA10090 0.9.0 2019.19) with Indian carrier LTE-M SIM and carried below steps to establish LTE-M communication with nRF Cloud: 1. Upgraded to latest...
Dear community,
I opened and successfully tried out the preflash_example. Since I will need a plain text NDEF message instead of an URI NDEF message as used in the example...
Hello,
I'm new to BLE and have a general question about concurrency and collisions. Sorry if a repeat question. I'm developing for nRF52832 using SDK 15.3 and S112 v6.1...
Hello,
I am testing nRF52 UART with DSP.
While transmit data in nRF52 (ADC results)
(example link: https://github.com/NordicPlayground/nRF52-ADC-examples )
I can show...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
The radio_tx_carrier() function was taken from example/peripheral...
So I bought a BLE Heart Rate Sensor (chest strap) from market. I am able to read data using the nRF Connect Android App. Now I am trying to read the Heart rate data using...
Hello,
I'm working with PCA10040 EVB.
I've followed this FAQ that shows how to add a device name.
But function sd_ble_gap_adv_set_configure() (called at the end of advertising_init...
Hi,
Forgive what may seem like a stupid question, but...
I would like to create a first reference PCB design using an nRF52832 for an IoT project I am working on.
I...
Hello,
For the function to acquire the FDS file system status, I noticed that the struct member variables are held in uint16_t. Some values, such as words_used and freeable_words...
nRF42840DK, SES V4.52c:
Project was copied from 17.0.0 to 17.0.2 and link now fails:
Building 'ble_app_att_mtu_throughput_pca10056_s140' from solution 'ble_app_att_mtu_throughput_pca10056_s140...
I have been trying to find some help or an example of using a capacitive sense button with the csense library(in SAADC mode) but also read the voltage of my battery using...
The Mac version of nRF Connect shows the Device Information Service characteristic Serial Number String as hex, not a string. It shows properly as a string on the iOS version...
