Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
For providing OTA function , I add dfu service into my own application APP1. and create another application App2 to copy the new firmware(named APP3) and cover the flash...
Please help me !
(spi_maseter_config.h at line 29)
#define SPI_PSELMOSI0 20u /**< SPI Master Out Slave In GPIO pin number. */
nRF51822 QFAA Package pin no.20 = P0.14...
I'd like to use 'Direct Advertising' to get the attention of a Central (a specific one or any in range) when an event happens on the peripheral. Is this mode supported by...
Hi,
I hooked up an nRF8001 (Olimex) to my logic analyzer and am observing the behaviour of the RDYn pin.
After resetting the nRF8001 through the RESET pin, the RDYn...
Hi All,
Just got my NRF51822 development board today and cannot get the heart rate demo from SDK to work. Two issues:
1> The PCA1004 board (the one without antenna)...
Dear Sir, We are intending to develop wireless UART- BLE module for our wearable product (Cable replacement profile). Please, help me to get to know about UUID and cable replacement...
Is sd_ble_uuid_vs_add available over the serialzation interface? How can we add a custom vendor ID over the interface if there isn't a serialzation function for it here ?
Hello,
I have made some current and timing measurements on the nRF51822 Development Kit (connected to a nRFgo Starter Kit) running some of the example applications provided...
I would like to drive an LED from the nrf51822 gpio
How much current can the nrf51822.
How much current can the nrf51822 gpio supply?
Is there a recommended LED for...
Hi. I am using a nRF8002 DK, and i am working with nRFgo Studio for 64 bits, in a windows 7 and windows 8 computers (for testing of the error purposes). I am having serious...
How to set READ property to a characteristic pipe through nRFGO studio.Actually i am not able to set READ property to any pipe.How can i do this?
Because i want iPhone...
Hi:
I use TIMER compare function, I open four channels and every channel produce interrupter.Here are some of my code:
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1->CC...
Hi. I've never asked a question here, and I'm a complete beginner to embedded programming, so I apologize if I break protocol in anything I do on here.
My setup:
nrfgo...
