Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi my friends, Nordic DevZone I have a project implemented on Bluetooth 5 network consisting of master and slaves ((1) master and slaves (7)) For example if I use (two kits...
I'm having an issue programming the bootloader using .hex file. I have "Erase all" by nrf52832 and was trying to debug my bootloader the code didn't stop at the beginning...
Dear Sir.
I have a question regarding the nRF9160 Interrupt procedure.
I have 2 interrupts on my nRF9160 custom board.
The 1st interrupt is an external interrupt every...
I'm using nrf52840 DK board with modified program of light switch example from sdk 2.1.1. While provisioning with interactive pyaci i'm giving provision address maually to...
Hi dear Nordic Team
I'am currently implementing a 802.15.4 compliant ShockBurst Radio TX/RX module on the NRF52811. As far as I understand there is a crc 16 implemented...
Dear All I had gone through nRFGO Studio for custom UUID But how to generate the Hex bytes so that i can put as in code for having custom service as shown below for above...
Hi community ! I'm testing Mesh characteristics by using debugger. Currently, i send messages through nodes and waiting for acknowledge, and I put a timer to get latency....
Hi,
present i am using nRF52840-DK for to develop the BLE application. here i am facing the debugging issue.
i.e. in my board i programmed S140 soft device. so after that...
Hi,
I am trying to read serial data via UART_1 with v1.2.0 SDK. According to dts-File UART_1 is configured with pin 0 and 1 on the devKit.
I added
CONFIG_SERIAL=y CONFIG_UART_INTERRUPT_DRIVEN...
Hi,
All was working on SDK 1.0. Now I have SDK 1.1 and new Segger and new nRF Connect and gnuarmbemb (I had a new computer, so did set up everything from scratch)
...
Hi,
I´m trying to work with the "TWI Scanner" example, provided by SDK 16. I Use nRF52833 DK (PCA10010), unfortunaly there is no solution for PCA 10010 in the SDK. This...
Which function is called nrf52832? When do I click the "enable CCCDs” function on the NRF Connect App, and which variables are the nrf52832 data set?
Step 1: Connect
...
Looking for help creating an example similar to the usbd_msc example that works with the W25N01GV . Currently using SDK 15.0. Would like to see this work with FatFS or possibly...
