In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
Hello,
I´m trying to connect the nRF9160-DK to the nRF cloud, using the asset tracker application. I was able to build and flash the application. But the DK can not connect...
Hello,
We are working through an issue which we found recently on the nrf sdk. The following is what is occuring:
We have two GPIO interrupts configured for low accuracy...
Hi... folks .. i am using nRF52840 development kit , i need to control the two servo motor using ble commands . I need to control the angle and speed of two motors , suggest...
Hello,
When I power our customer-designed nRF52832-based electronics I see the ingoing suply current (at 3.1V) rising in about 3 seconds up to 55 mA (!), then decreasing...
Hi, I have a problem with uart disable function (app_uart_close();). I started from ble_app_uart example, and I want to disable uart when nobody is connected to the Ble device...
Hi,
I have a similar problem to the case: ( devzone.nordicsemi.com/.../having-a-problem-with-preprocessor-options) with not being able to access the preprocessor options...
Hi,
As per the workaround of these errata its mentioned that "This code is already present in the latest sytem_nrf52.c file."
What does the latest mean here? Is there...
Hi,
I have two questions, one regarding nrfjprog and one regarding pynrfjprog:
How do I write content to a specific address of the flash using nrfjprog? Specifically...
I want to build custom commissioner app on nRF52840 DK. But when I'm running:
The error is OT_ERROR_ALREADY. I don't understand why, I am not invoking this method multiple...
I am using the nRF9160dk development board and I could not find a test or example for the internal RTC. could you provide a simple example of using the internal RTC.
Hy,
i get two warnings from my c++-compiler (arm-none-eabi-g++ (GNU Tools for Arm Embedded Processors 7-2017-q4-major) 7.2.1 20170904) if I use the header cmsis_gcc.h in...
