I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
In moving to the "rev-2 51422 silicon, we find that the app_timer inevitably fails after minutes to several hours. Power requirement moves from about .002ma to 4.5ma then...
Hi,
I am planning to use an external DCDC to supply the NRF51822 in Low Voltage Mode.
In the datasheet a voltage range of 1.75-1.95 on VDD and VDD1.8 is mentioned. ...
Dear all
I'm testing for RF stability. As i used 24LU1(host) with 51822(device) be the platform. For audio data transmission. 8k 8bits data rate.
Timeslot set as 1008us...
Hi,
I don't have any problems running the bootloader with S110 7.0.0.-3.alpha on the PCA1001 but when using the same code (minus the led and button config of the PCA1001...
Hi,
I am having a hard time with the permanent storage.
I got it to work with updating a 24 bytes long struct in a persistant block of 32 bytes.
I noticed that the...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hello Gentlemen,
I'm looking for a good example on how to pair BLE sensor and Android using static passkey. I looked at ble_app_gls but I could not see how they set the...
I have the following code
// bondmngr code comes here for now
ble_bondmngr_init_t bondInitData;
bondInitData.flash_page_num_bond = FLASH_PAGE_BOND;
bondInitData.flash_page_num_sys_attr...
I want to save data sent by the Nordic UART/Serial Port Emulation over BLE to the phone.
Can the Nordic UART app save received UART data sent over BLE to the phone?
I've tried adding in the examples (heart rate by example) the:
sd_app_evt_wait();
(including #include "nrf_soc.h" and #include "nrf_sdm.h")
Disabling led, etc. And...
I am running into some symptoms here that I'm not understanding.
My peripheral is an nRF51822 using the S110 softdevice. It implements a service which sends out notifications...
How can I view the private messages I have received using this devzone forum? I cannot find the inbox anywhere.
I have received a email saying I have received a private...
