I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I'm trying to pair my device (nRF82382) to nRF Connect (Dev Kit) and using another Dev Kit as a BLE_Sniffer. I'm trying to establish Pairing with LESC enabled. It's Pairing...
Hi community ! All is in the title.
The latency between sending the message and receiving the callback is not stable ( between 1600 & 4300 ms) I know that this delay is...
Hello, guys!
We are currently developing our firmware with nRF9160-DK and nRF Connect SDK v1.3.0. Among the other things, we need to communicate with the ultrasonic sensor...
Hi,
As we are in design phase of our custom board based on nRF9160, can you please let us know what all pins needs to be exposed in our design for collecting modem traces...
Hi Team,
I am trying to integrate a scheduler feature for my Thingy 91 using a nRF9160 DK kit. I searched for a few examples and found the one below in the link:
https...
Hello everyone,
I am developing a simple BLE node with an I2C sensor on it. Basically I just need to send over BLE the measurements made by that I2C sensor every minute...
Hello,
I am new to the Nordic environment and am trying to set up a beacon to scan and advertise using BLE.
I used the beaconing example ( https://github.com/NordicSemiconductor...
Hi, I have the same issue as in here: https://devzone.nordicsemi.com/f/nordic-q-a/62676/2-spi-devices-nordic-nrf52382 but for me the Debug/Release-toggle does not work. I...
Hi,
Can you confirm if TWI is supporting I2C clock streaching? Or and workaround to handle such a case.
As in attached picture is slave device requirements. Slave device...
Hello,
I’m using keil compiler.
My configurations are nrf51822ac/SDK12.3/s130_nrf51_2.0.1_softdevice.
I’m trying to migrate to SEGGER studio.
I’m referring to the...
In my case, I have 50+ devices as sensor and advertising measurements every 10 seconds, ADV_DURATION = 120s, use the 1E FF manufacturer data and self defined payload protocol...
i want to implement the nfc connection of pairing the nordic nrf52840 using SDK ver 15.0.0.
Can anyone help me in implementing this feature? because I'm new to this pairing...
Hello, all
I would like to ask about flash memory write errors.
When using version 12.1.0 of sdk, I was able to r/w to flash memory normally by using the sd_flash_write...
Based on sdk12.3, use 51-dk (51822) to run the ble_app_hrs routine. Use ios mobile phone to connect the device, it will automatically disconnect after 30 minutes, the disconnection...
The problem is not being able to connect to the device from an iPhone SE while the app is in background mode. We have an iOS app written in swift, which uploads data from...
