Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Problem:
I am trying send samples from SAADC to the NRFconnect app at 1kHz. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . I have...
Chip: nRF52832
SDK: 15.0.0
SoftDevice: S132 6.0.0
IDE: IAR EWARM 8.30
I have a peripheral-role application with __ICFEDIT_size_cstack__ = 0x800 (application call stack...
Hi Nordic:
I know mesh LPN can receive messages from it's friend node, that means when any other nodes send messages to LPN unicast address, LPN's friend node will buffer...
I have developed hardware utilizing an nRF52832 and am developing a bootloader for the system. I have had success following two tutorials: Getting started with Nordic's Secure...
Hi,
I'm trying to print a float over UART but I think the NRF implementation is faulty. I've tested not UART SDK example with the following changes, inserted at line 168...
I have a Thingy 91 and try to analyse the PSM and eDRX in asset tracker application. I use NCS 1.4.0 in this case.
In prj_thingy91_nrf9160ns.conf file I found the settings...
I have: nrf51822 bluetooth module, STlink V2, Keil, segger studio, nrf51 sdk and softdevice files.
I have achieved making the led blink at a ble peripheral device by nordic...
Hi,
I'm using nRF52840 with nRF5 SDK 16.0.0 and Mesh SDK 4.0.0.
I'm trying to add PB-GATT service to the ble_app_uart_coexist example. I set MESH_FEATURE_GATT_PROXY_ENABLED...
我正在执行ble_app_uart_c例程的功率测量，并且已经关闭了串行端口，这与打开串行端口时测量的波形不同。 我猜封闭的串口会影响扫描。
This is the waveform without closing the serial port
This is the waveform without serial port...
I add a compiler flag --wchar32 i n the Misc. Controls section of C/C++ to support character pointers with 32-bit width. But got errors as log attached. Any help is appreciated...
Hello guys,
I am a newbie with nrf52 and I am trying to debug ble_app_uart project under ble_peripheral directory. I do get download successful as shown in image below...
Hello,
I am trying to use the PPK (I) to measure current consumption of a DVK-BL654. I was able to successfully do this several months ago, and now when I am attempting...
Greetings,
I'm having some trouble displaying logs to the SES Debug Terminal... Basically, I can see the logs with RTTviewer but not in SES Debug Terminal. However printf...
