I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I intend to use the DFU BOOTLOADER in my product.
I’m using a PCA10040 DEV board for the tests with S132
I download the nRF SDK V17 and I compiled and I tested the...
I understand that nRF-9160 DK has Segger J-Link to program target devices / custom boards. Can this be used to program any ARM Cortex Debug Connector (10-pin)? Or I can program...
Hi. I am using nrf52840 with Softdevice 16.0.0 + BLE_uart_peripheral.
The SPI master transmits 2 SPI packets every 10 ms. At the the SPIS event handler, I call ble_nus_data_send...
I am seeing an issue when, after the pairing process is complete, during the BLE_GAP_EVT_AUTH_STATUS event, that the peer addr_id_peer field is always 0. For testing, I am...
My platform is nRF5_SDK_16. Softdevice is s140_nrf52_7.0.1_softdevice. I want to be the central role and scan nearby peripherals. Which function do I need to use? Which document...
I am totally new to nrf and just started with nrf52840. I've gone through certain tutorials available on youtube and some other on internet.
I've installed Segger embedded...
Assume that the Generic Level State is 0 and the following Generic Level Set message is received by a node.
Level: 0x7FFF Tid: 1 Delay: 0xFF (1275 ms) Transition time: 0x00...
I haven't been able to crack this one. Both pins confirmed as pull-up high using I notice when the peripheral is enabled the pins are pulled low (correct I think). Only sending...
Dear Nordic Developer Zone,
I want to change PHY configuration of ble_app_uart to 2Mbps.(SoC : nRF52811)
And I want to connect nRF52811 with iOS.(nRF connect for mobile...
Hi,
we reading out a Pressure-Sensor with TWI at the Sensor Server Model.
We get the Pressure-Data in an uint32_t and the measuring range in an uint16_t which have to...
From Mesh Model Specification 1.0.1.
"3.3.2.2.2 Receiving Generic Level Set / Generic Level Set Unacknowledged messages If the Transition Time field is included, the Delay...
I want to send larger UDP packets from nRF9160 (Thingy:91) using Serial LTE modem app.
I am not able to send more than 288 bytes of binary data.
How to send larger binary...
Hello, first, a little background info:
devzone.nordicsemi.com/.../
I want to know if I have successfully set the CCCD handle or not with my Android program.
And...
I've seen the Connectivity Bridge Application in the ncs, however I can't find any sample application for the nRF91 side showing how it can send/receive data and events from...
Hello
I have a cheap ST-link that I use heavylly to program STM arm cortex chip.
So my guess is that it should work for this case.
I am following this tutorial:
...
