Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm trying to create a siren tone using the pwm library, that ramps up and down between 2kHz and 3kHz.
Initially I started with the example provided in SDK v15.3.0 nRF5_SDK...
hello community!
Recently I got urgent job to rewrite sensor firmware to nrf52832.
Its not my project basically, another company project.
I wonder why rf52832 didn...
I understand with LTE-M they are supposed to offer greater distances to the cell site, but how do we tell how far away we are from the cell? In the good ol' days, we could...
It says under the S113 information that is supports extended advertising yet I can't see it in the API. I would like to take advantage of the 255 byte advertisement size for...
I want to use NRF9160 for development, now I want to pick something bootloader, so which one do I use
1. \ zephyr, replication, bootloader, McUboot \ zephyr
2. \ zephyr...
I am trying to develop a product with your nRF905. I have two units set up, and can read and write via SPI. However my concern is your poor documentation.
You do not say...
Hello, this is the person who asked about " devzone.nordicsemi.com/.../question-serial-output-uart ". First of all, thank you very much for your sincere reply.
The reason...
Hello
I would like to view the changes in sensor values in real time in a graph. Can you recommend a tool from Nordic or an easy-to-use program?
Thank you.
Sometimes during a DFU update, the NRF52811 can stay in bootloader mode (seen with name DFUTarg and mac_address equal to mac_address +1). I am on Softdevice 16.0 I'm using...
How to read values from 5 Analog pins at the same time
I know how to read from one Analog Pin, but i don't know how to access 5 analog pins at the same time and display...
Hello I am developing a prototype with the Thingy 91 that allows to have the default log in the UART0 <-> USB and collect the data of a sensor through the P6 expansion port...
I have a custom board using NRF52832 which communicates with a BMI160 accelerometer/gyroscope chip by SPI.
I have been developing in Segger Embedded Studio (v5.10d) in debug...
Is the nRF52840 sniffer is support to capture, decrypt and analyze the mesh specific data?
currently, BLE based sniffers can only able to saw a advertise data without any...
I am receiving an unexpected warning from nrf_atfifo_item_get that reports "Get failed - no item in the FIFO." This occurs when I start advertising using
void advertising_start...
Dear, Nordic.
I am developing with nrf52832.
I want to evaluate the characteristics of each version of BLE on specific hardware.
What I want to know is how to implement...
