Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi Devzone:
I am not sure if I should ask segger or here, basically I am trying to use Ozone for performance analysis.
I always get this message when starting:
Device...
Hi,
I am a Embedded System Engineer working is a Medical Device Company and presently compiling the code on on a previously licensed IDE and as, the licensing has expired...
Hello,
I'm working on porting a Secure Bootloader application for a project, and trying to understand how the macro is used NRF_BL_WDT_MAX_SCHEDULER_LATENCY_MS.
I don...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching/231773
We found sometime the LTE cannot be deactivated during the modem...
I want to try register level programming of Nrf52832 i.e low level programming. I referred your This GitHub repository but there are sill some libraries used . Is there any...
I am running an application with norma NUS Service with bonding.
When I want to make a DFU I start to write a token into the flash with fds and then do a soft reset. After...
Hi, I'm using nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 to develop a Zigbee Network. I'm using the ble_zigbee_template example as starting point of my works. I seen that...
Hello,
I have an nRF9160 DK and a Thingy:91. Both have been running asset_tracker for more than 3 hours, but none achieved an LTE Connection. I have installed the latest...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
Hi,
I am working on buttonless dfu example, but i want to design my application in such a way that, device should enter into dfu mode when button is pressed. I should be...
Hi, I have some issue about mesh network.
Using below developing environment.
- SEGGER Embedded studio for ARM V4.22
- nRF SDK 15.3.0
- nRF Mesh SDK 3.2.0
- chip...
Hello
I'm a beginner in Bluetooh and I bought two dev board NRF52840 DK. I would like to make a mesh with these two boards. One in master and the other in relay, the goal...
