hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi, I setup my attibute as 20B array. I'd like to change default data type in Presentation Format descriptor because the default value that is reported to me by BLE Scanner...
Hello,
I am curious to know what is the interpretation for the advertisement data
Advertising Data: 0201050709506562626c6503190002
This advertisement data seems to...
Hi,
Our custom board stops working after updating the connection parameters. We have a nrf51822 chipset custom board with proximity application flashed on it. Device get...
Dear Sir,
I open the Master Control Panel log.txt file, I can see
Serial port read: 04-3E-13-01-00-00-00-00 and
Serial port write: 02-00-00-09
Where can find the full...
I am using a nRF51822 at 16 MHz
What is the math formula behind the BAUDRATE register?
What is the timing error for each of the standard baud rate setting? This is not...
hello,
i was trying to run the sample examples, i tried blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. i was succesfull in getting the...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
Hi,
I need to drive a piezo buzzer. Just need to make a simple beep function(s) that one call will start generating a specified frequency on specified pin and other call...
there is no sample code in nrf5188 sdk to use BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM,
what's the difference between the two settings?
for BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM...
