Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
I have and older board which is the PCA10028 with the nRF51422 chip.
I have downloaded the nRF5 SKD 15.0.0 and found there is not example DFU project for my particular board...
Hello
I am working on a project based on the Mesh SDK 2.0.1 light_switch example. The system is using SD 6.0.0 and PCA10040 boards. DFU is successfully implemented on the...
Hi,
I work on nrf52832 with the serialization.
The nrf52832 connectivity part is load with S132 V6.0.0 (uart hci).
The stm32 will communicate with the 52832 throught...
Hello, can you say me:
1) which Stack parts in Mesh SDK: nrf5_SDK_for_Mesh_v2.0.1 are implemented in harmony with Bluetooth Mesh Profile Specification and which are not...
Hi,
We are attempting to send data via BLE every 100 ms using an app_timer. The app_timer sets a flag and in the while loop in main.c we call
ret_code_t err_code; do ...
Hello, i'm currently doing my own DFU central for the BLE DFU on SDK 13, i followed all the steps on this link , i created the init and image files with nrfutil and now i...
I am trying to connect my Ubuntu machine with my nrf52 custom board my setup is as follows, Ubuntu machine --> FTDI USB2UART --> HCI interface of nrf52 I can see on my logic...
My application (nRF51 S130 v2.0.1 SDK12.3.0) uses the Radio Timeslot feature for multiprotocol support similarly to the example in https://github.com/NordicPlayground/nrf51...
am trying to synchronize two nrf52840 thank's to state gpio with gpiote function but it return an error code 4 (No Memory for operation) whith this line -> NRF_LOG_INFO("no...
Hi Nordic Team,
What I want to achieve is to add a service with a custom 128-bit UUID that has about 4 characteristics with a completely different 128-bit UUIDs that are...
Hi Nordic,
I'm using NRF52832 to design a producation that needs four SPI interfaces.
The four spi peripherals are: gSensor, LCD, SPI Nor Flash, and PPG Sensor. Now...
Hi,
I'm working on a custom board with the nrf52840 engineering version n52840QIAABB with de SDK15. I've tried the exemple usbd_ble_uart from the SDK15 and it works well...
Figure 1. Data encoded and sent (attached)
Figure 2. Screen shot of wrong Time data (attached)
Here is some code that seems to be correct, sending 10 bytes that look...
Hi ,
I want to know how to give passkey to nrf8001 peripheral mode if it dont have display/keyboard/button, I have hear about justworks but not sure how it will work. Could...
Hello,
I am was playing around a bit with the twi_scanner-example and I figured out, that no matter if I chose the legacy-layer with nrf_drv_twi-functions or the new nrfx_twi...
