Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hi,
I am downloading my code to my custom board and sending commands through a USB virtual COM port. I basically echo and execute some GPIO operations after decoding the...
I have installed NRF 5X command line but I don't see it in my programs/start / desktop where will be the .exe file or how can I open that? How can I work with that ?
Hello ,
I am using 4 nrf52 DK for Mesh
1. how to I configure a Node as Relay
2. How do I capture MESH Packets/ Data from Mesh in Raspberry Pi and send to cloud
hi,
When working with Keil are the NRF_SDH_CLOCK_LF_RC_TEMP_CTIV & NRF_SDH_CLOCK_LF_RC_CTIV compiled as part of the nrf52810_xxaa project?
if not how can I compile...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
I started with the ble_app_template and a preexisting project written with sdk 12.
I have a custom service and 2 characteristics.
The point I am at now is that my DK advertises...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
I try multiple pins set. My pro code is here.
But this is not clear. I want to decrease my code line. Then I tried this.
I want to know where is my mistake?
I am trying to create a TDMA based network with the nRF24LU1+. I understand that nRF51 and nRF52 have the ability to trigger the transmission of a radio packet upon timer...
