Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Hi,
I was looking at the Thingy-52-to-nrf52xx demo. I want to capture raw motion data no a DK and save it for further processing. Are there any options (I guess one is nRF91...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
Hello,
I've created my own custom model which allows a client to control the duty cycle of a couple PWM outputs which are on the server. My model is quite simple, it just...
Dear all,
We're started studying payment via BLE with NRF52. But i looking for in Nordic website and google it seem a little subject and document. Can Nordic expert supply...
Hello,
I am getting really confused when using te SAADC to convert the read values into voltages.
I have seen that the example ble_app_proximity() uses the following...
I'm using 14.2 SDK SES . I'm trying to send data of sensor through BLE . When i enable Notification in mobile applicaion (nRF connect) i generally dont get any value or garbage...
Hello, I'm trying to port my code for driving spi memory (S25FL256S) from nRF51822 to nRF52840. I'm using nRF52840 Preview DK, S140 and SDK 15.0.0. On nRF51 I used custom...
Hello everyone,
I'm using PDK 52840 as Programmer/Debugger for our target board with nRF52840 chip. We have also other componen which need 2.5V voltage (down from 3v)...
I'm new to both the nRF52 family and SPI, and I'm working on an SPI master nRF52810 (using the PC10040e setup). I'm compiling using GCC and makefiles. I've set NRFX_SPIM_ENABLED...
