Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
Hi,
I'm using the light_switch example to implement mesh. How do I display the RSSI value of server on rtt viewer when the client receives the server status?
Regards,...
Is it possible to modify BLE_CONN_CFG_GAP after the softdevice has been enabled? I want to be able to set the event length on start up based on a setting stored in flash with...
Hello everyone, I am looking to make a small tracker using nRF52832 chip. Can anyone please suggest me a board and a coin cell having very small dimensions so that my tracker...
I am looking for a solution to create a very low latency (<10mS) audio link for continuous streaming.
Is the proprietary mode on the nRF52 series able to do that?
Is there...
hi
In Provisioner
in function app_default_models_bind_setup()
check the following lines
/* Bind health client to App key, and configure publication key */ ERROR_CHECK...
Hello,
I am creating a project through the MultiLink example.
One problem occurred. If the device is attached to NRF52DK, the connection will be disconnected immediately...
Hi,
I am running nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_hid_composite and find it can work in standalone mode. However, if I go to Keil or IAR debug session...
I created mesh networking using mesh SDK v2.0.1. And I have connected mesh to PC and smart phone.But it's a pity that the client can't receive the servers' RSSI (although...
Hi,
Need ESD protection recommendation for NRF51822.
While testing nrf51822, we noticed that when SWDCLK gets static dicharge over 900 V, nrf51822 reboots and current...
Hello,
I've been researching how to go about programming our devices on the production line. Most of the threads I've seen suggest two options: either to order them pre...
Hello,
which is the best solution for programming multiple nRF51822 using a Segger programmer ?
We have to produce a lot of BLE tags and i'd like to automatize programming...
We need a fast way to do production testing on our boards (based on nrf52832).
They have multiple peripherals that we would like to make sure were soldered correctly.
...
Hello,
I've been trying to figure out if this board with STM32F103 ( www.aliexpress.com/.../2042650923.html
can directly plug into my debug board
( www.aliexpress...
All,
We are in product on a product using the nRF52832 and are noticing in manufacturing that we aren't able to make it through the self test part of fab because of shoddy...
