Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi Dev Team,
I would appreciate if you can help me sort out the errors that I am getting when doing a DFU OTA using the 52 Dev Kit to the Thingy. I basically followed...
I have an input connected to P0.18 on my nRF52832, which needs to be driven high by an external source. I am running into two problems, which may or may not be related:
...
Hi,
I have seen some posts from
Ole
and
Hakon
about the bulk data transfer. But I have some confusions which I want to clarify before implementation.
I need...
When I update the firmware to version 2.1.0, the value that TVOC reads is always 0, whether or not it is related to the thingy gas sensor requires 48 hours of operation time...
So, after upgrade to Thread SDK 0.11, I'm not able to perform DFU again. Symptoms are identical to devzone.nordicsemi.com/.../ - this time on nrfutil v3.4, with pyspinel=...
How do you pan along the Y axis using the nrfConnect version of the PPK ? I can zoom in using the ctrl and right mouse button, then pan left and right, but I can pan up and...
SDK v14.2.0 using s132
Our central should only have one connection at a time, so I set
#define NRF_SDH_BLE_CENTRAL_LINK_COUNT 1
But when it is connected to a peripheral...
Hi Nordic,
In order to program our boards with nRF52832 devices in production, we need a stand-alone, command line programming tool.
I believe that the command line...
Hi everyone,
Maybe my problem has already been solved in another discussion, if so, I haven't found it yet !
I'm programming on a external board using nrf52832.
I...
Hi folks,
What's the maximum interrupt frequency the nRF51822 can support? I am looking to do an interrupt burst of about 4000 interrupts at a rate 2MHZ or 4MHz. In the...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello !
I have a big problem !
I explain : am using the NORDIC nRF52840 board (as slave), to answer to a microcontroller (the master), using SPI. My nRF52840 has to simulate...
Hello.
Some months ago I open this thread .
Yesterday talking with one member of android team, told me that the problem with "pairing/bond" persists with few Huawei phone...
