Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello,
What is the reason why my homemade PCB half passes through NRF_POWER->DCDCEN = 1; after broadcasting DCDC does not work? How do you need to solve it?
We will get a beacon from China. But how do we know if the chip is original? If I can read the unique device id, can I say it is original? Or is there another way?
I am working on the twi_sensor example,when i compiled the code it is showing as undefined symbol "data_handler(refered from main.o)", what are the changes i need to make...
Hi,
I was successfully changing mac address dinamically DURING ADVERTISING on nrf51822 chip at each ble_radio_notification event, in this way:
Before start advertising...
Hello
How do I activate Brown-out reset? I estimated there need to set some register/registers, but I cannot findout.
Possibly Brown-out reset function is always enabled...
Hello,
I work on project for BLE communication in DFU mode.
I am testing according to the mode defined on the Nordic web page link
I did the tests with the BleuZ and...
checking most of the reliable coin cell CR2032 such AS Panasonic declare on very very low current transfer far lower then 5 mA
if i set my Ble in 5mA IO OUT ....when my...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
I need to sample ADC channel at the fastest deterministic rate.
If i use burst mode with 3us acquisition time, do i get a sample exactly every 5us?
does t(conv) is always...
About example BLE_uart,
My device must always remain in advertising, I'm using a 1280 ms between two advertisng event.
I have to minimize the consumption during advertining...
I have a few questions about the NRF6707 Power Profiler kit and I would like to ask you: 1. The NRF6707 Power Profiler kit and nrf52 DK are linked through the ARDUIND D0 pins...
I am updating the application software that was created based on ble_app_multilink_central in SDK 9.0 to 12.3. When replacing device manager with peer manager, I received...
