Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello, I'm having trouble to make the image transfer demo work.
I flashed the .hex files found here: https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo to...
Hi all,
I am adding PWM to light switch server . I added success. PWM function run OK. I use PWM1,PWM2 with Timer 1 and Timer 3 and PWM library example .If I call function...
Dear Support Team,
I’m using nrf52832 and SDK 14.2.0. In my project ,there are two dsp,one is nrf52832 and the other is ntk658, they connect via uart with each other. ntk658...
Hi,
I am developing nRF52832 peripheral, SDK15.
Let me know about whitelisting.
I'd like to below functions.
1. Delete item(device) in white list.
2. Changeing...
Configuration is all 12 combinations of the following 3 x channels, 2 x modulations, and 2 x bit rates were tested to find the worst case. More substantial testing was to...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
