I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, I'm using nRF52832 with my custom board. (sdk 15.0.0)
I changed ble_uart example code, so I can receive GPS data through bluetooth.
Now, I have to send GPS data to...
Hello all.
few years ago, I made some product using nRF51822 on SDK v10.0.0
currently, I have to software update to use ECC(Elliptic Curve Cryptography) function on...
I'm using: nrf52832, SDK 15.0, SoftDevice S132 v6.0.
I'm trying to control a motor using an H-Bridge. If I simply do a nrf_gpio_pin_write to set forward/reverse to 1/0 or...
I have the nRF52832 PCA10040, V1.2.1, 2017.23 development board with ble_app_blinky_gcc_nrf52.ld RAM/FLASH settings:
MEMORY { FLASH (rx) : ORIGIN = 0x26000, LENGTH = 0x5a000...
Hi,
My freertos based application (SDK14.2) calls battery monitoring procedure every few minutes .
I've initialized the SAADC
Within the function I call
...
Hello, I have nrf52 and configure uart0 for connection with external device. I have configured it as NRF_SERIAL_MODE_DMA and set irq_handler .receive NRF_SERIAL_EVENT_DRV_ERR...
Hi,
May I ask, why read_resp is missing in struct ble_hid_report_record_t in sdk 15? Currently, I am migrating to sdk 15 from sdk 14.2. However, I didn't find any document...
Hi all,
I am doing an evaluation on NRF52 Smart Remote 3 for my company.
I am working on a Ubuntu 16.04 virtual machine with Ubuntu live CD for Smart Remote 3
-----...
What's the atomicity of flash writes on the nRF52832? If we crash while writing, say, 4 bytes, do we have a guarantee that either every byte or no bytes have been written...
Hellou, I am developing apllication , which is modification of light switch - client model.
I have problem by writing data to internal flash. When I write data to internal...
Hi
I've just modified our platform that uses a connectivity based environment to the latest S132 6.1.0/SDK15 combination. Since the migration I seem to miss a lot of scan...
Hi
I use the nRF51 Development Kit and the pin_change_int example.
when i push the button the LED changes but there is a delay of 16us.
is this normal ? can i speed...
Hello everyone,
Does this PPK able to measure current consumption of Arduino Uno R3? From the data sheet it say it has a standard Arduino Uno pin but i am not sure whether...
Hello Nordic Guys
We are trying to run ble_app_uart example on our custom hardware. SDK 15, SD132V6.0 . Problem what we experiencing is: NRD chip never goes to sleep,...
Hi,
I am Using nRF5_SDK_15.0.0 with nRF52 DK PCA10040 using Keil IDE.
I am going to Implement long string data write and read characteristic using custom service.
I...
