Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
My central device should scan and should get DIS of one peripheral and store in central and central should pass this information to other peripheral .
or
Central...
I am using nRF52832 with Beacon_App. I can able to get UID, Major, Minor, RSSI from my Raspberry PI using Python code.
I want to calculate the distance between my Raspberry...
I'm using S112 and SDK 14.2 to target NRF52810, but using the PCA10040 DK for now.
I've been coming back this issue multiple times over the past couple of months, still...
Hi @ll,
I tried to get the dfu example up and running but there are a lot of problems I encountered:
- Using the device_page_generator.py the string for the public key...
Hi @ll,
I have a problem bringing the pyaci up and running.
I used it successfully for everything before but since today it is making a mess again:
When I'm trying to...
I am using secure dfu bootloader from the SDK 12.
I changed the start address of my application. In the bootloader, in uint32_t nrf_dfu_init() { } , calling function nrf_bootloader_app_start...
Hello,
I want to make a simple UART Bridge between Central and Peirpheral. I'm usign nRF52832 with nRF5_SDK v15. There are central and peripheral uart examples in the...
Hi,
I have a working application with Buttonless Secure DFU Service wich runs on nRF52832. I'm able to perform DFU without bonds, but I want to use bonding in my application...
Direct connection after disconnect I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection...
Hi there
I met an error down below.
nrf_log_str_formatter.c(86): error: #29: expected an expression
if (RF_LOG_STR_FORMATTER_TIMESTAMP_FORMAT_ENABLED)
nrf_log_str_formatter...
Does the serial function operate with a soft device. Whenever i have an include statement for serial.h in a file with a softdevice I get a No such file or directory compilation...
I've been going off of the Buttonless DFU example to integrate DFU functionality into an existing project on a custom board. While I seem to have added the necessary includes...
I am programming a BL652 module (contains an nRF52832 with populated DC/DC inductors). I am programming it through the nRF52 DK in SEGGER studio.
When I run the blank (no...
Hi All,
A very general question here. I understand that using pre-defined services like the battery service help standardize the way peripherals send data to the central...
